dbx 1066
Fiche technique
- Fabricant : dbx
- Modèle : 1066
- Catégorie : Compresseur de studio
- Fiche créée le : 10/03/2005
Afficher les caractéristiques
| Input Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) |
| Input Type | Electronically balanced/unbalanced, RF filtered |
| Input Impedance | Balanced > 50 kOhm, unbalanced >25 kOhm |
| Max Input | > +24 dBu balanced or unbalanced |
| CMRR | Typically >50 dB at 1 kHz |
| Output Connectors | XLR and 1/4" TRS (Pin 2 and tip hot) |
| Output Type | Servo-balanced/unbalanced, RF filtered |
| Output Impedance | Balanced 120 Ohm, unbalanced 60 Ohm |
| Max Output | > +21 dBm balanced, > +20 dBm unbalanced |
| Sidechain Input Connector | 1/4" Unbalanced (Tip-Sleeve) |
| Sidechain Input Type | Unbalanced, RF filtered |
| Sidechain Impedance | >10 kOhm |
| Sidechain Max Input Level | >+24 dBu |
| Sidechain Output Connector | 1/4" Balanced TRS (tip hot) |
| Sidechain Output Type | Impedance balanced, RF filtered |
| Sidechain Output Impedance | Balanced 2 kOhm, unbalanced 1 kOhm |
| Sidechain Max Output Level | >+21 dBu balanced or unbalanced |
| Bandwidth | 20 Hz to 20 kHz, +0/0.5 dB |
| Frequency Response | 0.35 Hz to 90 kHz, +0/-3 dB |
| Noise | < -95 dBu, unweighted, 22 kHz measurement bandwidth |
| Dynamic Range | > 118dB, unweighted |
| THD+Noise | 0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), < 0.1% any amount of compression up to 40 dB, 1 kHz |
| IMD | < 0.1% SMPTE |
| Interchannel Crosstalk | < -80 dB 20Hz to 20 kHz |
| Stereo Coupling | True RMS Power Summing |
| Compressor Threshold Range | -40 dBu to +20 dBu |
| Compressor Ratio | 1:1 to infinity:1 |
| Compressor Threshold Characteristic | Selectable OverEasy® or hard knee |
| Compressor Attack/Release Characteristic | AutoDynamic™ |
| Compressor Attack/Release Modes | Selectable Manual or Auto |
| Compressor Manual Attack Time | Scalable program-dependent |
| Compressor Manual Release Time | Scalable program-dependent |
| Compressor Auto Attack Time | Program-dependent |
| Compressor Auto Release Time | Program-dependent |
| Compressor Output Gain | -20 to +20 dB |
| Limiter Threshold Range | +4 dBu to +24 dBu (off) |
| Limiter Ratio | infinity:1 |
| Limiter Type | PeakStopPlus® two-stage limiter |
| Limiter Stage 1 | PeakStop® brickwall limiter |
| Limiter Stage 1 Attack Time | Zero |
| Limiter Stage 1 Release Time | Zero |
| Limiter Stage 2 | Predictive intelligent program limiter |
| Limiter Stage 2 Attack Time | Program-dependent |
| Limiter Stage 2 Release Time | Program-dependent |
| Expander/Gate Threshold Range | Off to +15dBu |
| Expander/Gate Ratio | 1:1 to 30:1 |
| Expander/Gate Attack Time | < 100 µsec |
| Expander/Gate Release Time | Program-dependent |
| SC Ext. Switch | Routes the external sidechain input signal to the detector |
| SC Mon. Switch | Routes the sidechain signal to the output, interrupting the normal audio |
| OverEasy® Switch | Activates the OverEasy compression function |
| Countour Switch | Activates the frequency-dependent detector function |
| Auto Switch | Activates automatic program-dependent attack and release times, disabling the manual Attack and Release controls |
| I/O Meter Switch | Switches between monitoring input and output levels on the Input/Output Level meter |
| Bypass Switch | Activates the direct input-to-output hard-wire relay bypass. Relay automatically hard-wire bypasses unit at power-down and provides a power-on delay of 1.5 sec. |
| Operating Level Switch | (rear panel) Switches the nominal operating level between -10 dBV and +4 dBu simultaneoulsy for both input and output levels |
| ST Link Switch | Link both channels for stereo operation. Channel One becomes the master |
| Gain Reduction Meter | 12-segment LED bar graph at 1, 2, 4, 6, 9, 12, 15, 18, 21, 24, 27 and 30 dB |
| I/O Meter | 8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu |
| Compressor Threshold Meter | 3-segment LED bar graph at Below (-), OverEasy and Above (+) |
| Expander/Gate Threshold Meter | 2-segment LED bar graph at Below (-) and Above (+) |
| Limiter Threshold Meter | 1 LED to indicate PeakStopPlus™ limiting |
| Function Switches | LED indicator for each front-panel switch |
| Output Transformer Options | Jensen® JT-123-dbx or JT-11-dbx, BCI RE-123-dbx or RE-11-dbx |
| Operating Voltage | 100-120 VAC 50/60 Hz 200-240 VAC 50/60 Hz |
| Power Consumption | 20 Watts |
| Fuse | 100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T |
| Power Connector | IEC receptacle |
| Dimensions | 1.75"Hx19"Wx9"D (4.4cmx48.3cmx20.1cm) |
| Unit Weight | 5.1 lbs. (2.3 kg) |
| Shipping Weight | 7.5 lbs. (3.4 kg) |
Photos
Manuels et autres fichiers
Avis utilisateurs
Forums dbx 1066
Acheter neuf dbx 1066
Dernières petites annonces dbx 1066
Argus du dbx 1066
Avertissement
Les prix indiqués dans les petites annonces des particuliers sur Audiofanzine ne sont pas nécessairement les véritables prix de vente ou d'achat. Les annonces avec options, ou constituant un pack, ne sont pas prises en compte.
Moyenne des 119 annonces : 232 €
Moyenne des 2 annonces : 200 €
Moyenne des prix indiqués dans toutes les annonces : 232 €
Annonces des 12 derniers mois :
Argus Audiofanzine : 209 €*
* L’argus affiché par AudioFanzine est calculé en fonction de l’offre et de la demande, ce qui explique que sa valeur soit différente de la moyenne des annonces. Annonces des 12 derniers mois :
- 20 annonces de vente : 197 €
Argus Audiofanzine : 209 €*
** Prix correspondant aux achats effectués ces 12 derniers mois uniquement.
Cet argus vous semble erroné ? Merci de le signaler ici.
Compresseurs de studio concurrents
Autres Compresseurs de studio dbx
Autres catégories de Processeurs de dynamique
Autres dénominations : 10 66