Se connecter
Se connecter

ou
Créer un compte

ou
Agrandir
Ajouter ce produit à
  • Mon ancien matos
  • Mon matos actuel
  • Mon futur matos
Roland SYSTEM 100 - 104 "Sequencer"
Photos
1/49
Roland SYSTEM 100 - 104 "Sequencer"

Séquenceur hardware de la marque Roland appartenant à la série SYSTEM 100

Écrire un avis ou Demander un avis

Sujet Quels synthés peut on contrôler avec le module 104 ?

  • 7 réponses
  • 4 participants
  • 1 090 vues
  • 4 followers
1 Quels synthés peut on contrôler avec le module 104 ?

... à part le system 100 bien entendu icon_mrgreen.gif

2

Bon, je viens de voir que la tension du CV Gate est de 5 volts... c'est donc tout bon pour du Sequential Circuits ou du ARP mais bernique pour les Moog...

Pour ceux que ça intéresse :

Clock Oscillator Rate:

0.1Hz to 10Hz (X1 Mode)

1Hz to 100Hz (X10 Mode)
Clock Control: By "Clock Rate" control or external CV
Gate Time: 10% to 90% Variable Mark/Space
Gate Time Indicator On/Off LED
Step Number: 1-12 Steps
Channel Selector: CH-A or CH-B (allows sequences up to 24 steps)
Sequence Selector: One Time or Repeat
Start: Reset/Start
External Start Trigger Input +5V Threshold
Continue: Continue/Start
External Continue Trigger Input +5V Threshold
Stop: Stop
Stop End Pulse Output: +14V
Step: Step
External Step Trigger Input +5V Threshold
Voltage Register Range 0 to +2.5V, 0 to +5V and 0 to +10V selectable per 12
Gate Outputs: X2 +14V
Series CV Outputs: X2
Parallel CV Outputs: CH-A X2

CH-B X2
Physical:
Size: 280mm W x 355mm D x 145mm H
Weight: 5kg


Voltage: 100-120V 50-60Hz

220-250V 50-60Hz
Power Consumption: 5W Max
Additional Images:

http://www.bigbluewave.co.uk/roland_104.htm

 

[ Dernière édition du message le 04/10/2010 à 21:01:32 ]

3

J'ai quand même un doute headscratch.gif c'est mort pour contrôler un minimoog ??? icon_confused.gif

4

bin si , je ne vois pas pourquoi ça ne marcherait pas avec un moog ?

2eme LP disponible: (vynil & CD) https://summerbrackets.bandcamp.com/

5

A cause du S-trig sur le Moog :

Citation :

 

Gate (Trigger) also has two implementations:

  • V-Trigger ("voltage trigger", sometimes called "positive trigger"). This method involves keeping normally low voltage (around 0V) on trigger and producing a fixed positive voltage to indicate a note is on. The amount of voltage required differs from synth to synth, but generally it is from 2 to 10 V. V-Trigger is used by Roland and Sequential Circuits synths, among others.
  • S-Trigger ("short circuit trigger", sometimes called "negative trigger"). This one involves keeping voltage high normally, shorting the trigger circuit whenever the note should play. S-Trigger is used by Moog, Korg and Yamaha synths, among others.

Depending on the voltage level used, using the wrong combination of triggering mechanism would either yield no sound at all or would reverse all keypress events (i.e. sound will be produced with no keys pressed and muted on keypress).

On synthesizers, this signal is usually labelled as "Gate", "Trig" or "S-Trig".

 

 Le trig du Roland envoie du 0-5V

Le Moog attend l'inverse : 5-0V

6

Merci pour ta réponse Yohda icon_wink.gif et pour ta participation Foox  icon_biggrin.gif

Tu connais un sequenceur vintage pouvant contrôler un Moog ? headscratch.gif

Je sèche un peu là... icon_confus.gif

7

Dans l'absolu le problème v-trig/s-trig n'est pas insurmontable :

Il faut juste l'inverser et rajouter un offset pour le rendre compatible :

En gros le 104 fourni du +14V quand le pas est actif et du 0V quand il est inactif.

Si tu inverses le voltage, tu obtient -14V quand il est actif et le 0V ne bouge pas.

Ensuite tu utilises un offset de +14V, du coup ton -14V deviens 0V et le 0V du +14V, exactement ce dont le Moog a besoin.

Le Moog CP251 (par ex) permet l'inversion et l'offset, mais je ne pense pas qu'il produise suffisament (les 14V)

A vérifier, mais sinon pour un électronicien ça doit être très simple et peu honéreux.

8
Le 104 c'est aussi tout bon pour Oberheim.

D'après ce que j'ai lu récemment dans un autre topic, le 104 , comme le SQ-10, n'a pas de quantizer, ce qui veut dire qu'il peut aussi contrôler les Korg 700/770/800 (si on leur met des ports CV/Gate bien sur) et MS-10/MS-20/MS-50.

D'ailleurs j'aimerai bien un petit match Roland 104 vs Korg SQ-10 et connaitre la préférence de ceux qui ont pu utiliser les deux.